120 W. Main St.

Benson, NC 27504

(919) 894-2111

How May We Help You?

Mon - Fri: 7:00 - 6:00
Sat - 7:00 - 3:00

CLOSED ON SUNDAY

Signs Your Car’s Thermostat Is Going Bad (and What to Do About It)

Is your car overheating or running too cold? Learn the signs of a failing thermostat, whether it’s a DIY repair, and what steps to take to fix it with parts and guidance from Miller Auto Parts and Paint.
thermostat going bad

When your engine isn’t staying at the right temperature, it could be due to something as small — yet critical — as the thermostat. This component plays a major role in regulating your engine’s cooling system. If it fails, it can lead to overheating, poor fuel economy, or engine damage.

In this post, we’ll cover the common signs that your thermostat is going bad, whether it’s a repair you can handle yourself, and the step-by-step process to replace it if you decide to tackle it at home. And of course, Miller Auto Parts and Paint has everything you need to do it right.

What Does a Thermostat Do?

Your vehicle’s thermostat sits between the engine and the radiator. It regulates coolant flow by opening and closing based on temperature. When the engine is cold, the thermostat stays closed to help it warm up faster. Once the engine reaches optimal temperature, the thermostat opens to allow coolant to flow and prevent overheating.

If it fails in the closed position, the engine can overheat quickly. If it fails open, your engine may take too long to warm up, causing poor performance and fuel economy.

Common Signs of a Failing Thermostat

Here are the most noticeable symptoms that your thermostat might be going out:

1. Engine Overheating

If your temperature gauge spikes into the red zone or you see steam from under the hood, your thermostat might be stuck closed and blocking coolant flow.

2. Engine Running Too Cold

If the temperature gauge stays low after extended driving, the thermostat could be stuck open, allowing too much coolant through too soon.

3. Temperature Fluctuations

Rapid or unpredictable changes in engine temperature suggest the thermostat isn’t opening and closing at the right times.

4. Heater Not Blowing Warm Air

In cold weather, a stuck-open thermostat can prevent the engine from warming up enough to supply heat to the cabin.

5. Coolant Leaks Near Thermostat Housing

A failing thermostat can sometimes lead to pressure buildup, which may cause leaks around the thermostat housing or nearby hoses.

Is Thermostat Replacement a DIY Job?

Yes, for most vehicles, thermostat replacement is a straightforward DIY project — especially if you have basic mechanical knowledge and the right tools. The job typically takes one to two hours.

However, if your vehicle has a complex engine layout, or if you’re uncomfortable working with coolant or gaskets, you may want to leave it to a professional.

What You’ll Need:

  • Replacement thermostat (check with Miller Auto for the correct one)
  • New gasket or O-ring
  • Socket set and ratchet
  • Drain pan
  • Coolant (refer to your vehicle manual)
  • Scraper or gasket remover
  • Torque wrench (optional but recommended)
  • Gloves and safety glasses

How to Replace Your Thermostat: Step-by-Step

1. Let the Engine Cool

Never work on a hot cooling system. Wait at least 30 minutes after driving.

2. Drain the Coolant

Place a drain pan under the radiator and open the drain valve to lower the coolant level below the thermostat housing.

3. Locate the Thermostat Housing

Follow the upper radiator hose to the engine block — this usually leads directly to the thermostat housing.

4. Remove the Housing Bolts

Loosen and remove the bolts securing the thermostat housing. Carefully lift off the housing and set it aside.

5. Remove the Old Thermostat

Take note of the thermostat’s orientation, then pull it out. Remove the old gasket or O-ring and clean the surface thoroughly.

6. Install the New Thermostat

Place the new thermostat in the correct orientation. Install the new gasket or O-ring as specified.

7. Reinstall the Housing

Place the housing back in position and tighten the bolts evenly. Use a torque wrench if your manual specifies torque settings.

8. Refill Coolant

Top off the system with the proper coolant type. Bleed the system of air if your vehicle requires it.

9. Start the Engine and Check for Leaks

Run the engine with the radiator cap off to circulate coolant and watch for leaks. Keep an eye on the temperature gauge to ensure the thermostat is functioning.

Final Thoughts

A bad thermostat can cause serious engine issues if ignored. The good news is, with a little time and the right tools, it’s a manageable DIY fix for most car owners.

At Miller Auto Parts and Paint, we carry high-quality thermostats, gaskets, coolant, and tools to help you replace your thermostat with confidence. Not sure which part fits your vehicle? Our team can help you find exactly what you need and answer any questions you have along the way.

Need help choosing the right parts or supplies? Visit your local Miller Auto store — we’ll help you keep your car running at the perfect temperature.

120 W Main St, Benson, NC 27504

MON-FRI 7:00 AM – 6:00 PM

SAT 7:00 AM – 3:00 PM

SUNDAY – CLOSED

Contact Us