120 W. Main St.

Benson, NC 27504

(309) 733-4362

How May We Help You?

Mon - Fri: 7:00 - 6:00
Sat - 7:00 - 3:00


 Step-by-Step Guide For Changing A Flat Tire

At some point in every driver's life, the inevitable happens: you're cruising along, and suddenly you feel that dreaded wobble or hear the unmistakable thump of a flat tire. While it's an inconvenience, changing a tire is a fundamental skill every driver should possess. With the right tools, a little knowledge, and a bit of elbow grease, you'll be back on the road in no time. In this guide, brought to you by Miller Parts And Paint, we'll walk you through changing a car tire step by step.
changing a car tire

Safety First:

Before delving into the process, remember that your safety and the safety of those around you are paramount. Always change your tire in a safe location away from busy traffic.

Essential Tools & Equipment:

  • Spare tire (ensure it’s properly inflated)
  • Jack
  • Lug wrench
  • Owner’s manual
  • Safety gloves and goggles
  • Reflective safety triangles or cones

Step-by-Step Guide:

  1. Find a Safe Location:
    • As soon as you realize you have a flat tire, do not abruptly brake. Slow down and search for a safe, flat spot to pull over.
    • Turn on your hazard lights. If you have safety triangles or cones, place them behind your vehicle.
  2. Prepare Your Vehicle:
    • Ensure the car is in ‘Park’ mode. If you have a manual transmission, put it in ‘First’ or ‘Reverse’.
    • Engage the parking brake to prevent any movement.
    • Check the owner’s manual for any vehicle-specific guidelines.
  3. Remove the Hubcap & Loosen the Lug Nuts:
    • If your car has a hubcap covering the lug nuts, remove it. Some hubcaps might have a specific spot where you insert the flat end of your lug wrench to pry it off.
    • Using the lug wrench, turn the lug nuts counterclockwise. Don’t remove them yet; just loosen them a bit.
  4. Position the Jack & Lift the Vehicle:
    • Refer to your owner’s manual for the correct and safe jack placement.
    • Position the jack under the vehicle and pump or twist it (depending on its design) until the tire is off the ground.
  5. Remove the Lug Nuts & the Flat Tire:
    • Now, remove the lug nuts completely.
    • Grip the tire by its treads and gently pull it towards you until it comes off. Place it flat on the ground to ensure it doesn’t roll away.
  6. Place the Spare Tire:
    • Position the spare tire on the hub, aligning the rim with the lug nut bolts.
    • Push the tire into place.
  7. Hand Tighten the Lug Nuts:
    • Put the lug nuts back on the lug nut bolts and tighten them by hand initially.
    • Once they’re all on, tighten them further using the wrench, but not completely.
  8. Lower the Vehicle:
    • Use the jack to lower the vehicle, ensuring it’s securely on the ground.
    • Remove the jack.
  9. Tighten the Lug Nuts:
    • Now, tighten the lug nuts with the wrench, working in a star pattern. This ensures even pressure and alignment.
  10. Store All Equipment:
  • Place the flat tire, jack, and lug wrench back in your vehicle. Ensure everything is securely stored.

After the Change:

Once your tire is replaced, it’s essential to check the pressure of the spare tire as soon as possible. Also, remember that many spare tires aren’t meant for long drives or high speeds, so drive cautiously and get your flat tire repaired or replaced at your earliest convenience.

In Conclusion:

Changing a car tire is a valuable skill that can save you time, money, and stress. Regularly inspect your tires for wear and keep all necessary tools in your vehicle just in case. For all your auto parts needs and maintenance advice, Miller Parts & Paint has got you covered. Drive safely, and remember, with the right knowledge, you’re always in the driver’s seat!

120 W Main St, Benson, NC 27504

MON-FRI 7:00 AM – 6:00 PM

SAT 7:00 AM – 3:00 PM


Contact Us